Danatronics EHC-09DLW Ultrasonic Thickness Gauge

Description

Hello everyone.
This is the auction for
Danatronics EHC-09DLW Ultrasonic Thickness Gauge
.
This unit is in good working condition(tested!).
This product is the best model in EHC-09 series
(No other peripherals besides shown in the pictures)
We sell this unit to worldwide ebayers with the fixed international shipment fee .00(USD).
(Using international registered air parcel, it may take 10~15 working days to get to your location,
excepting buyer's customs clearance.)
Winner needs to give us receiver's phone number for prompt and exact shipment!
(Delivery agency in Korea does not accept international air parcel without receiver's phone number.)
If the unit is not the same as described, you can return the unit in 7 days.
Then, we can refund full amount of your bid with round trip cost of delivery right after we get the unit.
We can offer combined shipment for a little saving your delivery fee.
Thank you for your interest.
Size:
5" (127 mm) (L) x 3" (76.2 mm) (W) x 1.25" (31.75 mm) (H)
Weight:
8 OZ (.23 kg)
Thickness range:
0.020 - 20 inches (.50 mm - 508 mm) in steel, depending on material, temperature and transducer selection
Material Velocity Calibration Range:
0.0200 - 0.7362 in/uS (0.508 - 18.699 mm/uS)
Temperature:
Gage Operating: -4° F to 122° F (-20° C to 50° C) High temperature transducers available for material temperatures from -5° F to 950° F (-20.5° C to 510° C)
Battery life:
Up to 50 hours (20 hours with backlight on)
Battery type:
2 "AA" Alkaline
Display:
128 X 64 Graphics LCD monochrome, sunlight readable
Language support:
multi language of English, French, Spanish, Italian, Czech, German, Portuguese, Slovak, Finnish, Hungarian and Chinese on select models
Information displays:
Loss of signal (LOS), min, max, large reading while displaying min at the same time, velocity, zero, calibration, units, freeze, unfreeze, % battery life remaining, gain - low, std, high, echo to echo symbol
Resolution:
.001" (.01 mm), .01" (.1mm) user selectable
Probe recognition:
Via a pick list from a menu
Delay line auto zero measurement:
Auto at power up with listed numeric value. Ideal for correcting delay line wear/curvature and for transducer acoustic drift at elevated temperatures
Package:
IP54 rated Custom, splash-proof, high impact plastic with illuminating rubber keypad for go/no-go testing
Bandwidth:
0.5-20 MHz (-3dB)
Units:
English/Metric/Microseconds
Gain:
Low, Standard and High for varying test conditions (for gages without a waveform) or 1 dB steps from 20-90 dB or Automatic Gain Control (AGC) for gages with a waveform
Fast Min/Max Mode:
Simultaneously displays minimum or maximum and actual thickness value at 20 measurements per second
Differential Mode:
Displays the difference from the actual thickness measurement in absolute or percentage of a user entered reference value
Alarms:
Minimum/Maximum depth, vibrates, beeps and display flashes as well as keypad illumination
Illuminating keypad:
F1 = Red, F2 = Yellow and F3 = Green for easy go/no-go testing
Ergonomics:
User selectable lefty or rightly display changes via keypad
Backlight:
Light Emitting Diode, On/Off or Auto On based on valid readings or last key press
Shut off:
Auto, user programmable time out (1-31 minutes), after no reading/key press or never shut off
Protective pouch:
Custom molded pouch with wrist strap and belt clip (Optional, standard on DLW and DL gages)
Transport case:
Hard Plastic with high density molded foam cut out for gage and most accessories
Freeze mode:
Freezes display (ideal for high temperature readings)
Hold mode:
Holds display to retain last thickness reading
Standard EHC-09 Inclusions:
Ultrasonic thickness gage, DKS-537, 5 MHz 0.375 inch diameter potted cable, Data XL interface program, couplant, and transport case. See chart below for standard inclusions for each gage
Warranty:
Limited 2 year warranty on parts and labor for gage only under normal use
Transducers:
A wide variety of dual transducers from 1-10 mhz, high temperature duals, delay lines and pencil probes. Note the EHC-09A only works with the DK-718, DK(S)-537 and the DC-250.